Tentesol is KMG Investment Flat Glass’ reflective solar control glass.

 Tentesol can be used as monolithic and also it can be incorporated into Insulating Glass Unit (IGU). IGU assembled with Temperable Low-E Glass provides savings from heating expenses in addition to solar control property.

Colors:

 Silver, green, gray, bronze and blue colors are available.

 Tentesol is intended primarily for facades and/or windows of commercial buildings, balcony glazing; and provides solutions to interior architecture in terms of partition walls and decorative applications.

 Tentesol is manufactured by applying a thin, reflective and highly durable metal oxide coating on clear or tinted glass during the production of float glass

Single Glazing

 The above figures are valid for 6 mm monolithic KMG Investment Tentesol.

 “Daylight” and “Solar Energy” properties are calculated with “TNO Science and Industry - WIS 3.01” program using spectral measurements in compliance with EN 410.

 “U-value” is calculated with “TNO Science and Industry - WIS 3.01” program according to EN 673. The emissivity measurements used for calculations are in compliance with EN 673 (Annex A) and EN 12898.

 Thermal stresses or building codes may require the use of heat-treated glass. This document is not an evaluation of the risk of glass breakage from thermal stresses. Please contact KMG Investment Flat Glass to ensure the correct form of glass to be supplied for the structure.

 Specifications, technical and other data are based on information available at the time of preparation of this document and are subject to change without notice.

 Trakya Cam Sanayii A.Ş. cannot be held responsible for any deviation between the data introduced and the conditions on site. This document is only informative, in no way it implies an acceptance of the order by Trakya Cam Sanayii A.Ş.

  Daylight Transmittance (%): The ratio of the visible spectrum (light) that is transmitted through glass.

  Daylight Reflectance (outdoor) (%): The ratio of the visible spectrum (light) that is reflected outside by glass

  Solar Factor: The percentage of total solar radiant heat energy entering the room thorough the glass. The lower solar factor means better solar control.

  U value (W/m2K): A measure of the rate of heat loss of a building component. The lower U value means better heat control and more comfort in winter.

Insulating Glass Unit With Clear Float Inner Pane

 The above figures are valid for IG units incorporating with 6 mm KMG Investment Tentesol outer pane, 12/16 mm air space and 6 mm inner pane.

 “Daylight” and “Solar Energy” properties are calculated with “TNO Science and Industry - WIS 3.01” program using spectral measurements in compliance with EN 410.

 “U-value” is calculated with “TNO Science and Industry - WIS 3.01” program according to EN 673. The emissivity measurements used for calculations are in compliance with EN 673 (Annex A) and EN 12898.

 Thermal stresses or building codes may require the use of heat-treated glass. This document is not an evaluation of the risk of glass breakage from thermal stresses. Please contact KMG Investment Flat Glass to ensure the correct form of glass to be supplied for the structure.

 Specifications, technical and other data are based on information available at the time of preparation of this document and are subject to change without notice.

 Trakya Cam Sanayii A.Ş. cannot be held responsible for any deviation between the data introduced and the conditions on site. This document is only informative, in no way it implies an acceptance of the order by Trakya Cam Sanayii A.Ş.

  Daylight Transmittance (%): The ratio of the visible spectrum (light) that is transmitted through glass.

  Daylight Reflectance (outdoor) (%): The ratio of the visible spectrum (light) that is reflected outside by glass

  Solar Factor: The percentage of total solar radiant heat energy entering the room thorough the glass. The lower solar factor means better solar control.

  U value (W/m2K): A measure of the rate of heat loss of a building component. The lower U value means better heat control and more comfort in winter.

Insulating Glass Unit With Low-E Coated Glass (Low-E coating on the 3rd surface) Inner Pane

 The above figures are valid for IG units incorporating with 6 mm KMG Investment Tentesol outer pane, 12/16 mm air space and 6 mm inner pane

 “Daylight” and “Solar Energy” properties are calculated with “TNO Science and Industry - WIS 3.01” program using spectral measurements in compliance with EN 410.

 “U-value” is calculated with “TNO Science and Industry - WIS 3.01” program according to EN 673. The emissivity measurements used for calculations are in compliance with EN 673 (Annex A) and EN 12898.

 Thermal stresses or building codes may require the use of heat-treated glass. This document is not an evaluation of the risk of glass breakage from thermal stresses. Please contact KMG Investment Flat Glass to ensure the correct form of glass to be supplied for the structure.

 Specifications, technical and other data are based on information available at the time of preparation of this document and are subject to change without notice.

 Trakya Cam Sanayii A.Ş. cannot be held responsible for any deviation between the data introduced and the conditions on site. This document is only informative, in no way it implies an acceptance of the order by Trakya Cam Sanayii A.Ş.

 Daylight Transmittance (%): The ratio of the visible spectrum (light) that is transmitted through glass.

  Daylight Reflectance (outdoor) (%): The ratio of the visible spectrum (light) that is reflected outside by glass.

 Solar Factor: The percentage of total solar radiant heat energy entering the room thorough the glass. The lower solar factor means better solar control.

  Shading Coefficient: The ratio of solar factor of a particular glass type to the solar factor of 3 mm clear float glass, set in identical conditions. The lower shading coefficient means better solar control.

  U value (W/m2K): A measure of the rate of heat loss of a building component. The lower U value means better heat control and more comfort in winter.

Quality

  KMG Investment Tentesol is manufactured in accordance with EN - 1096 Glass in Building - Coated Glass.

 The above figures are valid for IG units incorporating with 6 mm KMG Investment Tentesol outer pane, 12/16 mm air space and 6 mm inner pane

 “Daylight” and “Solar Energy” properties are calculated with “TNO Science and Industry - WIS 3.01” program using spectral measurements in compliance with EN 410.

 “U-value” is calculated with “TNO Science and Industry - WIS 3.01” program according to EN 673. The emissivity measurements used for calculations are in compliance with EN 673 (Annex A) and EN 12898.

 Thermal stresses or building codes may require the use of heat-treated glass. This document is not an evaluation of the risk of glass breakage from thermal stresses. Please contact KMG Investment Flat Glass to ensure the correct form of glass to be supplied for the structure.

 Specifications, technical and other data are based on information available at the time of preparation of this document and are subject to change without notice.

 Trakya Cam Sanayii A.Ş. cannot be held responsible for any deviation between the data introduced and the conditions on site. This document is only informative, in no way it implies an acceptance of the order by Trakya Cam Sanayii A.Ş.

 Daylight Transmittance (%): The ratio of the visible spectrum (light) that is transmitted through glass.

  Daylight Reflectance (outdoor) (%): The ratio of the visible spectrum (light) that is reflected outside by glass.

 Solar Factor: The percentage of total solar radiant heat energy entering the room thorough the glass. The lower solar factor means better solar control.

  Shading Coefficient: The ratio of solar factor of a particular glass type to the solar factor of 3 mm clear float glass, set in identical conditions. The lower shading coefficient means better solar control.

  U value (W/m2K): A measure of the rate of heat loss of a building component. The lower U value means better heat control and more comfort in winter.

Quality

  KMG Investment Tentesol is manufactured in accordance with EN - 1096 Glass in Building - Coated Glass.